maf00040aem mn103sj9 series type MN103SFJ9D internal rom type flash rom (byte) 64k ram (byte) 4k package (lead-free) qfp044-p-1010f minimum instruction execution time 16.7 ns (4.5 v to 5.5 v) ? interrupts 8 external interrupts 30 internal interrupts: watchdog timer. timer. serial i/f. pwm. a/d conversion ?nish. system error. fail-safe function ? timer counter 8-bit timer 8 timer 0 to 7 ........... interval timer. event count. cascading connectable 16-bit timer 3 timer 16 ................ interval timer. event count. pwm output. double buffer timer 18 ................ interval timer. event count. pwm output ( 6 pins simultaneous output are available). double buffer timer 20 ................ interval timer. double buffer. start synchronized with 3-phase pwm are available watchdog timer 1 ? serial interface uart (full duplex) /synchronous interfaces selective 3 serial 0, 1 ............... 1-bit to 8-bit transmission (synchronous). 2 and 3 channel type selectable (synchronous) ? i/o pins i/o 30 : common use 30 ? a/d converter 10-bit 1 unit. 12-bit 1 unit. 8 channels minimum conversion time: 1.0 s simultaneous conversion of 2 series are available conversion start synchronized with 3-phase pwm or timer 20 are available ? motor control pwm 16-bit 3-phase pwm triangular waveform or jigsaw waveform. dead time setup. double buffer. output polar switching is available. pwm output pin protect function ? clock monitoring function the stop of the system clock or abnormal frequency of the system clock can be detected ? reset automatic reset ? internal oscillation 10 mhz ? electrical charactreistics (a/d converter characteristics) parameter symbol condition limit unit min typ max non-linear error 10 bit / 12 bit 3 lsb a/d conversion time tad 1.0 s analog input voltage via vss vdd v ta = 25 c. vdd = 5.0 v. vss = 0 v
maf00040aem MN103SFJ9D ? pin assignment qfp044-p-1010f adin00, pc 0 adin01, pc 1 adin02, pc 2 av ss adin03, pc 3 vr ef + av dd adin04, pc 4 adin05, pc 5 adin06, pc 6 adin07, pc 7 nrst vppe x vdd5 osci osco vs s p01, irq01, tm1io vout18 test2, sd at a test1, scloc k p00, irq00, tm0io irq1 1, tm18o3, tm16bio, p5 1 pwm00, p8 0 npwm00, p8 1 pwm01, p8 2 npwm01, p8 3 pwm02, p8 4 npwm02, p8 5 tm18o4, tm18aio, p6 0 vss tm18o5, tm18bio, p6 1 vdd 5 p50, tm16aio, tm18o2, irq10 p41, tm7io, tm18o1, irq09 p40, tm6io, tm18o0, irq08 p25, sbi 1 p24, sbt1 p23, sbo 1 p22, sbi 0 p21, sbt0 p20, sbo 0 p03, irq03, tm5io p02, irq02, tm4io 1 2 3 4 5 6 7 8 9 10 11 22 21 20 19 18 17 16 15 14 13 12 33 32 31 30 29 28 27 26 25 24 23 34 35 36 37 38 39 40 41 42 43 44
request for your special attention and precautions in using the technical information and semiconductors described in this book (1) if any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) the technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. no license is granted in and to any intellectual property right or other right owned by panasonic corporation or any other company. therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) the products described in this book are intended to be used for general applications (such as office equipment, communications equipment, measuring instruments and household appliances), or for specific applications as expressly stated in this book. consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automotive equipment, traffic signaling equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. it is to be understood that our company shall not be held responsible for any damage incurred as a result of or in connection with your using the products described in this book for any special application, unless our company agrees to your using the products in this book for any special application. (4) the products and product specifications described in this book are subject to change without notice for modification and/or im- provement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (5) when designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (esd, eos, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. when using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) this book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20100202
|
